Tag: MC-E

Posted on

Ultrafire C2 modded with a Cree MC-E

Ultrafire C2 with Cree MC-E
Ultrafire C2 with Cree MC-E

In late 2007, I bought a couple of Ultrafire C2 flashlights. They were nicely made for an inexpensive flashlight and they used Cree XR-E LEDs (P4 bin).

Last fall, I modded one of my C2s with a Seoul Semiconductors Z-Power LED P7. The P7 is a quad die LED. I made it direct drive running off a single Li-Ion 18650 battery. There were mods that could be made for a circuit board to drive the P7 but I was too lazy to make one.

I recently found a 3-Mode Regulated Circuit Board for Cree MC-E and SSC P7 LEDs (SKU 1217) sold by Shiningbeam.com that advertises an output current of 2500 mA on high. It has only three modes: high, medium and low. The 17mm diameter of the board is a direct fit in many pills, including a lot of P60s and the Ultrafire C2. I used one of the boards to improve a DealExtreme P60 MC-E drop-in.

I had another of the Shiningbeam boards and a quad die Cree MC-E LED, so I decided to put them in my other Ultrafire C2.

Ultrafire C2 pill with Cree MC-E
Ultrafire C2 pill with Cree MC-E

I soldered the LED to a trimmed down DealExtreme Star Connection and Heatsink for Cree MC-E LED Emitters – Parallel (SKU 16545). I’m not sure why they call it a parallel board, because each die is separately addressable with the connections on the board. I soldered all the anodes together and all the cathodes together, so it would run in parallel.

With a fully charged Li-Ion 2400 mAh battery, I measured the current at a little over 2700 mA through the tailcap. After five minutes, the flashlight was hot, but not so hot that I couldn’t touch it. It also dimmed slightly from initial turn-on but it is still brighter than my P60 MC-E mod.

With a McClicky switch in the tailcap, this is a really nice, bright flashlight now.

Posted on

Cree MC-E LED P60 Drop-in

The current high lumen output LEDs use multiple chips on a single die. The Seoul Semiconductor Z-Power LED P7 and the Cree XLamp® MC-E LED are two examples that are in popular use by flashlight modders.

DealExtreme Cree MC-E LED 3-Mode Drop-in Module

I recently bought a DealExtreme Cree MC-E LED 3-Mode Drop-in Module ($18.30 USD) for my Surefire 6P flashlight (the 6P body is bored to work with a single 18650 battery).

The DealExtreme P60 size drop-in works with 2.7V~4.2V – a single Li-Ion 18650 battery, single RCR123A battery or CR123A battery. There is also a not too low level mode and annoying strobe mode. In the Surefire 6P host (about 5.2″ long – 13.2 cm), the DealExtreme Cree MC-E drop-in is an extremely bright flashlight in a small package. There is an extensive list of similar sized flashlights that use P60 size drop-ins in this Candlepowerforums.com thread.

DealExtreme seems optimistic in their description of the MC-E drop-in brightness as 410 lumens. It has more flood and less of a hot spot than the Malkoff M30. For comparison, my Malkoff Devices M30 output is rated at a realistic 235 lumens. My SSC P7 mod, inspired by jirik_cz, gives me the feeling that I am seeing everything. If not for the $125 USD cost, I would be all over the Malkoff M60 MC-E (NLA).

In my flickr set below, there are beamshots comparing the Cree MC-E, Cree XR-E and SSC P7. I centered the beam of each light on the scrawny tree against the fence.