MintyBoost 3.0

Posted by Mr. Leslie Wong On October - 13 - 2012

MintyBoost

 

I built a pocket size USB charger using a MintyBoost 3.0 USB charger, a 3.7 v, 2600 mAh LiIon battery and a built-in LiIon battery charger in an Altoids Wintergreen Mints tin. It can be used to recharge a cell phone, iPod or other small USB rechargeable device.

I’ve had adafruit.com‘s MintyBoost 3.0 kit and USB LiIon/LiPoly charger (this is v1.1) for a while but I never put them together. I liked the size of the Altoids gum tin of the previous MintyBoost versions I have built but I wanted a little more charging capacity than 2 AA batteries could provide. I wanted a suitable battery and enclosure that didn’t compromise charging capacity and size.

Using ladyada’s calculations for battery power, I decided to use a 3.7v 2600 mAh LiIon battery.

The battery’s capacity:
MintyBoost mWh = 3.7V * 2600 mAh = 9620 mWh input

The amount of current it can provide:
Output mAh @ 5V = 9620 mWh / 5 * 80% = 1539 mAh output (80% is the conversion efficiency)

Number of iPhone 4S recharges = 1539 mAh / 1430 mAh (iPhone battery capacity) ~ 1.1

The MintyBoost kit requires the soldering of a few components to a circuit board. I also made two mods to the internal battery charger. With this version (1.1) of the adafruit LiIon battery charger, removing the resistor R4 and replacing it with a 1K ohm resistor allows the internal battery to be charged at 1000 mA.

The internal battery charger has connections for external status LEDs. I connected current limiting resistors between the board and LEDs, then mounted the LEDs in holes in the Altoids tin. The green LED indicates that the internal battery is charging and the yellow LED indicates a fully charged battery. (LiIon/LiPoly charging tutorial at Adafruit Learning System)

The battery and circuit boards are mounted in the Altoids tin with double sided foam tape. I made a miscalculation in the height of the LiIon charger taped to battery – the cover won’t close when the charging cable for the internal battery is attached.

To charge the internal battery, a USB Mini B plug supplies the power to the internal battery charger as in the photo above. To charge a device, a USB Standard A connector is used. There’s also enough room in the Altoids tin for storing an Apple 30-pin to USB Cable.

MintyBoost 3.0 in Altoids Wintergreen Mints tin

Below are charging test results with an iPhone 4S starting with battery at 49%:

Time (minutes)      Charge (%)
0:00                           49%
0:15                           58%
0:30                           66%
0:45                           75%
1:00                           83%
1:15                           89%
1:30                           93%
1:45                           96%
2:00                           97%

If you are interested in the MintyBoost design process: http://www.ladyada.net/make/mintyboost/process.html

Bruno Senna Cautions Against Using an iPhone While Driving

Posted by Mr. Leslie Wong On May - 3 - 2011

Bruno Senna, in a visceral driving demonstration in a 2010 Formula One Renault R30, advises against using your iPhone while driving, especially going through Eau Rouge at the Circuit de Spa-Francorchamps. The drive (and doughnuts) took place at the World Series by Renault last week.

The Man Behind the Apple Aesthetic

Posted by Mr. Leslie Wong On September - 23 - 2007

As senior vice-president of design at Apple, Jonathan Ive is the man behind the design of the iMac, the iPod, and the iPhone.

read more | digg story

iPhone Unlocked

Posted by Mr. Leslie Wong On August - 24 - 2007

Hackers have been working on unlocking the iPhone since its release. Today Engadget is showing a video using iphonesimfree.com‘s software to unlock the iPhone.

Apple iPhone

What’s this mean? You’re no longer locked into a $1,389 first year cost (phone+minimum service plan) for an iPhone in the US. You can choose the provider you want and use any SIM card from any network provider in any country.

 

Will It Blend – iPhone

Posted by Mr. Leslie Wong On July - 11 - 2007

iPhone Hits eBay

Posted by Mr. Leslie Wong On June - 29 - 2007

Or you could just get one for retail at the Apple Store. And wouldn’t a nerd start taking it apart as soon as possible?

Sponsored Links

About Me

I like Alfa Romeos, art, barbecue, baseball, bicycling, cars, cigars, computers, cooking, eating, electronics, fly fishing, football, Formula 1, friends, golf, horology, jazz, movies, museums, photography, r/c cars, r/c helicopters, reading, restaurants, Scotch whiskey, softball, slot car racing, tennis, the internets and travel

Twitter

    Photos

    DSC_5298DSC_5285DSC_5360DSC_5377DSC_5381DSC_5368DSC_5356DSC_5353DSC_5354DSC_5345DSC_5352DSC_5339